Denso RC5 Spécifications Page 100
- Page / 182
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
80
4.2.11 Robot Failure (Output)
(1) Function
The signal outputs to the external device that a problem, such as a servo
error and a program error, occurs with the robot.
(2) Terminal number
No. 3 of connector CN10.
(3) Usage
The signal is used to light the robot failure indicator lamp of an external
operating panel.
The signal is used to help the PLC clear an error in response to a
ROBOT FAILURE signal.
(4) ON conditions
As shown below, the signal will be turned ON under the following conditions.
When an error, such as a servo error, a program error and undefined
program, occurs at the start of the program and during execution of the
program.
When an error occurs during execution of the program in internal
operation by the operating panel or the teach pendant or in external
operation by the PLC.
When an error, such as undefined program, occurs at the start of the
program only in external operation.
Caution: The signal will not be output when an error, such as a program
input error occurs in manual operation, except when a servo
error occurs in manual operation. For further information, see
"ERROR CODE TABLES."
(5) OFF conditions
As shown below, the signal will be turned OFF under the following
conditions.
When a CLEAR ROBOT FAILURE command is input from the external
device and the existing error is cleared.
When the existing error is cleared by operating the Cancel key of the
operating panel or the teach pendant.
バリティーエラー、
「Cancel」キー操作
Robot Failure Output
⋅
Prog
r
am number, parity error, or an undefined program number at
external start.
⋅ The robot errors during automatic operation (both internal operation and
external operation).
⋅ When CLEAR ROBOT FAILURE and OPERATION PREPARATION
START signals are input.
⋅ When the Cancel key of the operating panel or the teach pendant is
operated.
Robot failure
- INTERFACE MANUAL 1
- Preface 3
- How this book is organized 5
- 3. Installation Precautions 9
- SAFETY PRECAUTIONS 11
- Warning 13
- Contents 17
- RC5 - VSE 6 B A - P 21
- 2.3 Setting the parameter 23
- /HM-E series 24
- <Front> 25
- [ 1 ] Specifications 27
- [ 2 ] Outer Dimensions 29
- Location of IPM boards 30
- (VM-D, VS-E, HS-E, and HM-E) 32
- (VS-D, VC-E, H 33
- -D, and XYC-D) 33
- 2.2 Switching between Modes 34
- 2.3.1 Standard Mode 42
- 2.3.2 Compatible Mode 43
- 2.4.4 User Input Commands 44
- 2.4.5 User Output Commands 45
- Chapter 3 46
- (5) OFF condition 47
- 3.2.2 Auto Mode (Output) 48
- 3.2.4 Servo ON (Output) 50
- 3.2.6 Normal CPU (Output) 52
- (4) ON condition 54
- 3.2.11 SS mode (Output) 56
- 3.4.1 Enable Auto (Input) 59
- 3.4.2 Robot Stop (Input) 60
- (2) Terminal 61
- Halt OFF (open) 62
- Dedicated to Standard Mode 65
- [ 2 ] Strobe Signal (Input) 69
- [ 4 ] Status Area 71
- 3.5.3 I/O Commands Details 72
- (2) Format 73
- (3) Description 73
- 3.5.3.4 Error Read (0100) 77
- Type I Variable Read (0110) 79
- 3.5.3.9 I/O Write (1001) 83
- 3.5.3.10 I/O Read (1010) 84
- (1) Equipment setup example 85
- Chapter 4 89
- 4.2.2 Auto Mode (Output) 91
- 4.2.3 Servo ON (Output) 92
- ⋅ CAL EXECUTION and OPERATION 93
- 4.2.6 Teaching (Output) 95
- 4.2.10 Normal CPU (Output) 99
- (1) Function 100
- (2) Terminal number 100
- (3) Usage 100
- (4) ON conditions 100
- (5) OFF conditions 100
- (1) Function 101
- 4.2.14 Error No. (Output) 103
- 4.2.16 SS mode (Output) 104
- (4) Contact 105
- (Compatible Mode) 106
- 4.4.1 Enable Auto (Input) 107
- The mode is switched to 109
- external mode 109
- (2) Terminal numbers 110
- 4.4.4 Program Start (Input) 112
- 1-cycle Operation 112
- Program Start Operation-2 113
- Program Start Operation-3 114
- 1→T2→T3 in the figure 116
- 4.4.5 Program Reset (Input) 118
- 4.4.6 Robot Stop (Input) 120
- ON (shorted) 122
- 50 ms. or more required 122
- Instantaneous 122
- (e.g., conveyor) 126
- (2) Outline of procedure 127
- Operation start area check 128
- Operation position 1 ON 128
- Automatic operation 129
- Operation end 129
- Executing single-cycle 129
- [ 1 ] From the teach pendant 131
- [ 2 ] In WINCAPSII 132
- Parameter details 134
- User I/O signal lines 137
- Chapter 5 138
- 5.2.4.1 Standard type 152
- Check point (2) 156
- Chapter 6 158
- 6.2.4.1 Standard type 172
- Check point (1) 176
- Chapter 7 I/O Wiring 178
- : 230 VAC, phase R 180
- B: 230 VAC, phase S 180
- C: Not used 180
- D: Ground 180
- RC5 CONTROLLER 181
Produits connexes et manuels pour Robotique Denso RC5
Robotique Denso RC5 Spécifications
(138 pages)
(138 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels