Denso Power Net Terminal BHT-103 Manuel d'utilisateur télécharger pdf (Page 44)

BHT-700BB-CE/700BWB-CE/700BWBG-CE

2.5.3 Auto Power OFF

The power turns OFF automatically when the BHT is not used for the length of time set at the user

program.

The default time is set to 3 minutes when the BHT is shipped from the factory.

− Point − Do not remove the battery cartridge while Auto Power OFF is processing.

Failure to observe this may result in data stored in the BHT being lost.

* Refer to “Chapter 4 System Operation” for details of auto power OFF.

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 175 176

Preface 2
About this Manual 4
− Searching by Word 6
SAFETY PRECAUTIONS 8
Handling the BHT 10
Contents 13
Outline 17
1.1 System Configuration 18
1.1.2 Software Configuration 19
1.2.1 BHT Front/Rear 20
42-Keypad 22
1.2.2 Keypad 24
1.2.3 BHT Screen 28
BHT Preparation 31
1. Disconnect the hand belt 33
4. Disconnect the hand belt 36
2.2.3 Battery Voltage Drop 39
2.3 Attaching the Stylus 40
2.3.3 Using the Stylus 41
2.4 Initial Setup 42
2.5 Turning OFF the Power 43
2.5.3 Auto Power OFF 44
2.6.1 Reset 45
2.6.2 Reset Method 45
2.6.3 Full Reset 45
2.6.4 Full Reset Method 45
Basic Operation 47
3.1 Scanning Barcodes 48
27-Keypad 50
3.3 Using the Keypad 52
3.4 Transmitting Data 54
3.4.2 Infrared Communication 56
3.4.3 Bluetooth 57
3.4.4 Wireless Communication 58
System Operation 61
4.1 Desktop 62
 Remote Desktop Connection 64
4.2 Start Menu 65
 Windows Explorer 66
 Command Prompt 66
 Favorites 66
 Documents 66
 Task Bar and Start Menu 74
4.3 System Menu Outline 75
4.3.1 System Menu Structure 76
Power key> 78
GPRS> 78
4.4 System Menu Details 79
4.4.2 Communication Menu 80
 Uploading 84
Open the wireless device 88
[Connect] button 88
4.4.3 System Properties 91
− Note − 98
Barcode Handy Terminal 101
4.4.4 HardTest Menu 109
 USB Interface Test 112
4.4.5 Explorer 118
4.4.6 System Information 118
 IP Information 120
∗： No entry or no selection 122
4.5.2 Editing in RF Control 124
Communication 129
5.1 Connector Communication 130
5.2 Infrared Communication 131
5.3 Bluetooth 132
Communication 132
5.3.2 Specifying Parameters 133
5.4 Wireless Communication 134
Ymodem Communication 135
 Vertical Parity 136
5.5.2 Ymodem Communication 137
5.6 ActiveSync 138
Maintenance 141
2. Disconnect the hand belt 142
6.4 Daily Maintenance 147
Error Messages 149
7.1 System Errors 150
Specifications 153
8.1 Specifications 154
8.1.2 Barcode Specifications 155
Barcode Label Size 156
Appendices 159
9.1 CU-700 Functions 160
9.2 Components and Functions 161
9.3 CU-700 Power Supply 163
9.5 Charging the BHT 167
9.6 CU-700 Specifications 169
9.8 Inserting the SIM Card 174
DENSO WAVE INCORPORATED 176

Commentaires sur ces manuels

Pas de commentaire

Denso Power Net Terminal BHT-103 Manuel d'utilisateur Page 44

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de codes-barres Denso Power Net Terminal BHT-103