Denso BHT-200QW Manuel d'utilisateur

Barcode Handy Terminal BHT-904BB User’s Manual

ix BHT-904BB Handling the BHT Mishandling of the BHT-904BB may result in electrical shock, overheating, or smoke generation. Please read the follow

84 BHT-904BB  nment 1. NICATION menu nd then press the ENT key. Th2. r keys ([▲] [▼]) or numeric keys ([1]]) to select the deress the Backspace/c

85 Barcode Handy Terminal “3: COM PORT”: Setting the interface port 1. Select “3: COM PORT” at the SET COMMUNICATION menu and then press the ENT ke

86 BHT-904BB Select “1: Ymodem” at the PROTOCOL TYPE menu to display the screen on the right. “1: CR/LF”: Specifies handling for line delimiters in r

87 Barcode Handy TerminalSelect “3: BHT-Ir Protocol” at the PROTOCOL TYPE menu to display the screen on the right. nter the ID number of the BHT usin

88 BHT-904BB  on condition setting for the user program (OPEN “COM:”) creae system mode setting can be used. Therefore, it is not necessa1. elect “

89 Barcode Handy Terminal[6] Defining the functions of the Shift key and Magic keys 1. 2. s ([1] [2] [3] [4] [5] [6] then press the ENT key. : SHI

90 BHT-904BB  “2: M1 KEY” - “6: M5 KEY”: Defining the Mx key functions 1. Select “2: M1 KEY” to “6: M5 KEY” at the SET KEY menu and then ET Mx KEY

91 Barcode Handy Terminal Defining the Backspace/clear key function The Backspace/clear key deletes the last character entered (backspace). When th

92 BHT-904BB [7] Setting the TCP/IP, FTP and DHCP Use the following procedure to change the TCP/IP, FTP and DHCP settings. 1. Select “7: TCP/IP” a

93 Barcode Handy Terminal“2: IP ADDRESS”: Setting the IP address cursor keys ([▲] [▼]) or numeric keys ([1] [2] [3]) to highlight (2) The mode chang

x Barcode Handy Terminal Handling the CU  If smoke, abnormal odors or noises come from the CU, immediately unplug the AC adapter from the wall s

94 BHT-904BB  1. nd then press the NT key. 2. thePreironment : SERVER IP”: To(1)lays, allowing the setting to be entered with the lay) and alphabet

95 Barcode Handy Terminal“2: OPTION”: Setting the FTP options Select “2: OPTION” at the SET FTP menu to display the screen on the “1: CR/LF”: e serve

96 BHT-904BB  1. nu and then press the NT key. Thrrent setting. Pr Presto display the NETWORK ( creen for . Pr (DHCP) screen to retur T quired IP c

97 Barcode Handy Terminal[8] Setting the user prog ram execution option Use the following procedure to set the user program execution option. 1. E

98 BHT-904BB [9] Operation related to the drive Use the following procedure to carry out the operation related to the drive. 1. TEM 2/2 menu and

99 Barcode Handy Terminal [10] Setting the operation log Use the following procedure to set the operation log. 1. OPERATION LOG” at the SET SYSTEM

100 BHT-904BB 4.5.7 Use the following procedure to perform a BHT operation test. the right. cts thPERSelects the beeper scale test. Selects the agi

101 Barcode Handy Terminal[1] Barcode reading test Use the following procedure to perform a barcode reading test. 1. Select “1: BARCODE” at the TEST

102 BHT-904BB Barcode Type and Corresponding Characters Displayed on the Screen ID Characters Barcode Type Codemark Type1 Codemark Type2 *3 EAN-13（JA

103 Barcode Handy Terminal Setting the Barcode reading Test Options Press F1 key at the TES reen to set the barcode reading test options. The screen

xi BHT-904BB To System Designers  When introducing BHTs in those systems that could affect human lives (e.g., medicines management system), devel

104 BHT-904BB [2] 1. en press the ENT ey. ays as shown on the right, and the BHT reads and writes ata to and from all areas of the RAM and performs

105 Barcode Handy Terminal[3] Beeper scale test Use the following procedure to perform a beeper scale test. pon completion of this test, the BHT aut

106 BHT-904BB [5] LCD and indicator LED tests LED test. The TEST BEEPER screen displays as shown on the right. 2. ress the ENT key. The entire s

107 Barcode Handy Terminal4. A 1-dot frame is displayed around the screen and the LED is illuminated en. ar key or press the SF and 5. ress the ENT

108 BHT-904BB [6] FThe file test allows deile test tailed information on program fi elect “6: FILE” at the TEST menu and then press ed to the name

109 Barcode Handy Terminal◆ Font files (*.FN3/FN4) 1. ace/clear key to return to the previous sc ◆ 1. key Press the Backspace/clear key to retu

110 BHT-904BB ◆ Other files (*.DAT, *.TXT) Press the Backspace/clear key to return to the previous screen. If four or more fields exist, “MORE FIEL

111 Barcode Handy Terminal[7] Communication test Use the following procedure to perform a communication test. 1. Select “7: COMMUNICATION” at the TE

112 BHT-904BB 3. d at the y. an error occurs, the tested slave BHT beeps three times and displays s. ( X X ) ta is different from the sent data. 2:

113 Barcode Handy Terminal USB conneHave a USB cable ready and then connect the BHT to the hoction test 1. st. 2. TEST COMMUNICATION screen anur

xii Barcode Handy Terminal Handling the CU  Never disassemble or modify the CU; doing so could result in an accident such as fire or malfunction.

114 BHT-904BB [8] Key-entry, beeper and vibrator test Use the following procedure to perform a key entry, beeper and vibrator test. Select “8: KEY &

115 Barcode Handy Terminal[9] PING test Use the following procedure to run the PING test. 1. Select “9: PING” at the TEST menu and then press the EN

116 BHT-904BB Upon completion of the PING test, the screen displays as shown on the und during the PING test. ok pl r of screen)right. The PING re

117 Barcode Handy Terminal 1. elect “2: SET PING” at the TEST PING menu and then press the NT key. ATA SIZSpecifies the data size of the echo reque

118 BHT-904BB PING Echo Request Transmission Timing (SEND TYPE) Two types of echo request send timings are available: TYPE 1 and TYPE 2. After sendin

119 Barcode Handy Terminal 1. elect “3: SET DEVICE” at the TEST PING menu and then press . c ey to return to the TEST PING menu. “3: SET DEVICE” (P

120 BHT-904BB 4.5.8 BHT system information. 1. 6: VERSION” at the SYSTEM MENU and then press the he SYSTEM INFORMATION screen displays as shown on t

121 Barcode Handy Terminal [1] Functions for which licenses have been registered () 1 ction that has been registered, and then press the ENT ke

122 BHT-904BB [2] U-911 System Information Display information. 1.2. Select “6: VERSION” at the ENTTh ays as shown on the right. ress the M2 key.

123 Barcode Handy Terminal4.5.9 Downloading/Uploading Files by FTP (FTP MENU) Use the following procedure to download and upload files by FTP. the EN

xiii BHT-904BB Declaration of Conformity DECLARATION OF CONFORMITY Directive 99/5/EC (R&TTE) We, DENSO WAVE INCORPORATED, hereby declare at our

124 BHT-904BB 2. Use the cursor keys ([▲] [▼]) to highlight the item to be set, and then press the ENT key. try (no guidance dio delete a single char

125 Barcode Handy Terminal[2] Uploading by FTP 1. the ENT key. The screen displays as shown on the right if uploadable files exist. . RECTORY]:

126 BHT-904BB 3. Enter the directory and file name, or select a file, and then press the ENT key. DIPress the Backspace/clear key to return to the F

127 Barcode Handy TerminalFTP Download/Upload Messages When the BHT is uploading or downloading files by FTP, the following messages will appear at t

128 BHT-904BB Response Messages from the FTP server w. estart marke eady aconnecti rt transferring. atus oka ection. d oka e t h e. m status rr

129 Barcode Handy Terminal4.5.10 to perform the Bluetooth® wireless communication settings. 1. Se the DEVICE MENU and then press the ENT key. Th [1[2

130 BHT-904BB [2] Bluetooth® parameter setting menu 1. then press the ENT key. Select “2: SET BLUETOOTH” at the BLUETOOTH MENU and Switches to the

131 Barcode Handy Terminal pecifying device detection parameters Select “2: INQUIRY” at the SET BLUETOOTH menu and then ems are displayed. : INQUIR

132 BHT-904BB  Specifying master station parameters 1. Select “3: MASTER” at the SET BLUETOOTH menu and then press the ENT key. The current setting

133 Barcode Handy TerminalSetting the serial port profile (SPP) service for connection target isplay the screen on the right. service name for the c

xiv Barcode Handy Terminal FCC and IC Regulations (For North America) This equipment has been tested and found to comply with the limits for a Class

134 BHT-904BB  Select “4: SLAVE” at the SET BLUETOOTH menu aSpecifying slave station parameters 1. nd then press The current ayed. [2: TIMEOUT]:

135 Barcode Handy Terminal  Specifying file transfer protocol options ENT key. : ock. the data block. : H.PARITY”: “OFF”: Disables the addition o

136 BHT-904BB [3] Detecting remote devices Select “3: BROWSE DEVICE” at the BLUETOOTH MENU and : INQUIRY]: Switches to the device detection scre

137 Barcode Handy Terminal 5. Use the cursor keys ([▲] [▼]) or numeric key ([3]) to highlight [3: NUpress the ENT key. M RESPONSES] and then 1: DO IT

138 BHT-904BB The confirmation screen on the right appears. To specify the selected address as a remote device address, select ing, select “2: No”

139 Barcode Handy Terminal  1. menu he screen on the right appears. : TIMEOUT]: Sets the time for services inquiry. ress the Backspace/clear key

140 BHT-904BB When the service inquiry is complete or ®when the time for service inquiry has elapsed, the Bluetooth device address of the destinati

141 Barcode Handy Terminal  1. maximum of three authorized remote device addresses is displayed. ress the Backspace/clear key to return to the BROW

142 BHT-904BB [4] File transfer with serial port profile 1. Select “4: SERIAL PORT” at the BLUETOOTH MENU and then press the ENT key. The screen on

143 Barcode Handy Terminal 7. Use the cursor keys ([▲] [▼]) or numeric key ([1]) to highlight n starts. return to the SERIAL PORT MENU. hen the con

xv BHT-904BB

144 BHT-904BB 4.5.11 USB Communication settings (“DEVICE” MENU) follory. efaThe USB communication settings following system initialization are as Do

145 Barcode Handy TerminalUse the following procedure to set the USB communication settings. [1] 1. Select “1: USB” in the ICE menu and then press

146 BHT-904BB [3] MTP RESTRICTIONS menu 1. Select “1: Mand then preTP RESTRICTIONS” in the MTP SETTING menu ss the ENT key. 2. Use the cursor keys (

147 Barcode Handy Terminal[5] MTP DISP FILTER menu ” in the MTP SETTING menu and then press the ENT key. The MTP DISP FILTER menu (FILE ATTRBUTE)

148 BHT-904BB 4.5.12 Deleting Program/Data Files (DELETE FILE Menu) Delete program files or data files stored in the FLASH ROM. 1. The DELETE FILE

149 Barcode Handy Terminal4.5.13 Deleting Font Files (DELETE FILE Menu) Delete font files stored in the FLASH ROM. If there is insufficient user area

150 BHT-904BB To delete font files: Use the cursor keys ([▲] [▼]) or numeric key ([1]) to highlight [1: Yes] and ace/clear key to return to the DELET

151 Barcode Handy Terminal4.5.14 METER Menu) t he same settings can be set at another BHT by copying the system pat computer and so on. le at another

152 BHT-904BB [1] Downloading the BHT system parameter file Use the cursor keys ([▲] [▼]) or numeric key1. ([1]) to highlight 2. hile the dow

153 Barcode Handy Terminal[2] Uploading the BHT system parameter file 1. Use the cursor keys ([▲] [▼]) or numeric key ([2]) to highlight [2: UPL

1.1 System Configuration･･････････････････････････････････････････････ 2 BHT-904BB Chapter 1 Outline This chapter describes the

154 BHT-904BB 4.5.15 REMOTE WAKEUP Menu) 1. he SET REMOTE WAKEUP menu displays as shown on the right. : REMOTE WAKEUP]: Enables or disables remote w

155 Barcode Handy Terminal4.5.16 Downloading/Uploading the System Message File (SYSTEM MESSAGE Menu) The system message file is a file (file name:

156 BHT-904BB [1] Downloading the system message file Use the cursor keys ([▲] [▼]) or numeric1. key ([1]) to highlight aiting for the system me

157 Barcode Handy Terminal[2] Uploading the system message file 1. Use the cursor keys ([▲] [▼]) or numeric key ([2]) to highlight [2: UPLOAD] a

158 BHT-904BB 4.5.17 1. he MODIFY MENU screen displays as shown on the right. : SYSTEM MODIFY]: Updates the BHT system. [2: CU-F/W MODIFY]: Update

159 Barcode Handy Terminal When the Displayed File Name Differs from the BHIf the name of the file displayed at [2: FILENAME] differs fromT System

160 BHT-904BB [2] Updating the CU-911 system Update the CU-911 system after downloading the CU-911 system update file. (Refer to section “4.2.2 CU-9

161 Barcode Handy Terminal If the System Update File Does not Exist when Updating the CU-911 System Download the CU-911 system update file and upda

162 BHT-904BB

BHT-904BB Chapter 5 Communication This chapter describes technical information relating to the IrDA communication and Bluetooth® w

2 BHT-904BB 1.1 System Configuration This section describes the hardware required for the barcode data collection system used by the BHT and the BHT

164 BHT-904BB 5.1 IrDA Communication The BHT has a built-in IrDA communication device that enables wireless transfer of programs and data both betwe

165 Barcode Handy Terminal 5.1.1 IrDA Communication Port Transmission Speed Communicating Device Transmission Speed BHT-900 Series 9600, 19200, 3

166 BHT-904BB 5.2 Bluetooth® Wireless Communication 5.2.1 Usage Precautions  It may be possible to avoid the easy occurrence of communication error

167 Barcode Handy Terminal 5.2.2 Setting Parameters  Bluetooth® Device Address Remote devices return these addresses, uniquely assigned to each Blu

168 BHT-904BB 5.3 USB Communication The BHT can communicate with the host computer via the USB communication port. The Connection method “COM” and “M

169 Barcode Handy Terminal 5.3.2 USB communication by MTP 1. Set the BHT USB connection mode to MTP. For details, refer to “4.5.10 USB Communicat

170 BHT-904BB  Important  Receiving the BHT-BASIC data files (Method of specifying the field information) The data files received via the MTP conn

171 Barcode Handy Terminal 5.4 Basic Communication Specifications and Parameters 5.4.1 Basic Communication Specifications The table below lists the

172 BHT-904BB  Transmission Code and Bit Order  All characters should be coded to 7 or 8-bit code for data transmission.  The standard code at t

173 Barcode Handy Terminal 5.4.2 Communications Parameters In System Mode and user programs written in BHT-BASIC, you can set the communications par

3 Barcode Handy Terminal  Host Computer Allows you to edit, manage and download user programs and data, as well as downloading system programs. Mode

174 BHT-904BB

BHT-904BB Chapter 6 Maintenance This chapter describes battery replacement and daily procedures for taking care of the BHT. 6.1

176 BHT-904BB 6.1 Replacing the Battery Batteries are not included in the package. Have the battery specified by DENSO WAVE ready. Specified battery:

177 Barcode Handy Terminal 4. Check the battery terminals on a new battery and indications on the BHT unit and then insert the battery in the directi

178 BHT-904BB 6.1.2 Charging rechargeable batteries When using rechargeable batteries, it is possible to charge with the BHT main body as follows.

179 Barcode Handy Terminal 6.1.3 Rechargeable Battery Service Life Rechargeable batteries are consumable products. The longevity of the battery vari

180 BHT-904BB 6.2 Daily Maintenance 6.2.1 Proper Care of the BHT Wipe any dirt from the BHT housing, charge terminals, and BHT or battery cartridge

BHT-904BB Chapter 7 Error Messages This chapter describes causes and countermeasures for error messages that display during BHT use.

182 BHT-904BB 7.1 System Errors The error messages that display on the screen and the causes and countermeasures to be taken if an error occurs when

183 Barcode Handy Terminal Message BHT Response Cause Countermeasure The BHT displays this error message and automatically runs the execution program

i BHT-904BB Preface Thank you for using the BHT-904BB DENSO WAVE Barcode Handy Terminal. Please read this manual thoroughly prior to operation to e

4 BHT-904BB 1.1.2 Software Configuration This section describes the software used for BHT Series application development and application in addition

184 BHT-904BB Message BHT Response Cause Countermeasure The message continues to display. When the BHT is turned on, no user programs are found. Cont

185 Barcode Handy Terminal 7.2 System Mode Errors When error messages display while running System Mode, refer to the following table and take appro

186 BHT-904BB Message Cause Countermeasure The file you attempted to upload is damaged. To upload the damaged file as is, press the [1] key. The mem

BHT-904BBChapter 8 8.1 BHT-904BB Specification ･･･････････････････････････････････････ 188 8.1.1 Hardware Specifications････････

188 BHT-904BB 8.1 BHT-904BB Specification 8.1 r (LR6) (x 2) or AA rechargeable battery eneloop® (HR-3UTGA) (x 2) (L)Ambient operating te teries) Amb

189 Barcode Handy Terminal 8.1 cifications rted Barcode Types Bar Dimensions Scan Magnification .2 Barcode SpeSuppoBarcode Type Univers uct codes 1

190 BHT-904BB 8.1.3 Reading Performance Reading Reference Position Reading Distance and Area Narrow Bar W epth of Field

191 Barcode Handy Terminal *1 The dotted ) indicateble width of ditions: - Ambient illuminance: 500 Lx. (Xenon arc lamp) Narrow bar: Wide ba

192 BHT-904BB 8.1. rface SpecificatioIrDA Interface IrDA Ver1.3 Lo ompliant m sween BHT units: CU-901: 960021: 4608Bluetooth® Interface Compatible sp

Barcode Handy Terminal BHT-904BB User’s Manual First Edition, November 2010 Second Edition, March 2011 The purpose of th

5 Barcode Handy Terminal [3] Software Used at the BHT Unit The BHT unit FLASH memory has a system area and user area, with the system program stor

6 BHT-904BB  Font File These files are required to display JIS 1 and 2 standard Kanji characters at the BHT unit LCD display. By using font files, t

7 Barcode Handy Terminal 1.2 Component Names and Functions 1.2.1 BHT Front/Rear (1) (3)(2) (5)(4) (8)(6) (7) (9)(12)(11

8 BHT-904BB 1.2.2 Keypad/BHT Screen The BHT key functions can be set at user programs. The diagram below shows an example of settings for each key f

9 Barcode Handy Terminal NO. Key Name Function and Description (9) ～ Function keys Used to select functions. * The functions of the function

10 BHT-904BB If the system display is set to ON at the system settings or in the user program, icons display at the bottom of the screen (default) in

BHT-904BB Chapter 2 BHT Preparation This chapter presents information on how to load the battery, turn ON/OFF the BHT power, and

12 BHT-904BB 2.1 “BHT Preparation” Procedure Follow the steps below to prepare the BHT for use. 2.2 Loading the Battery (Page 13) First load the ba

13 Barcode Handy Terminal2.2 Loading the Battery Batteries are not included in the package. Have the battery specified by DENSO WAVE ready. Specified

ii Barcode Handy Terminal Customer Registration and Inquiries Customer Registration To allow us to provide our customers with comprehensive service a

14 BHT-904BB Mishandling of the battery may result in electrical shock, overheating, smoke generation,combustion, or blowout. Please read the follo

15 Barcode Handy Terminal2.2.1 Battery Power Level Indicator Confirming at the Power Level Icon The battery power level can be confirmed at the batt

16 BHT-904BB 2.3 Wearing the Hand Strap Wear the hand strap to prevent the BHT from being accidentally dropped during use. 2.3.1 Attaching the Han

17 Barcode Handy Terminal2.4 Initial Setup (Setting the date, time, and message language) Turn ON the power after inserting the batteries into the B

18 BHT-904BB 5. Press numeric key [1] or [2] and ENT key to select either of the following items. 1: Easy Pack Ad Activates the easy operation applic

19 Barcode Handy Terminal2. Press the SCAN key to activate the Easy Pack Ad for BHT-900. The screen on the right appears.  Point  When the M1 key

20 BHT-904BB 2.6.2 Turning the Power OFF after Data Back-up 1. Hold down the Power key ( ) for at least 3 seconds. The message right displays and

21 Barcode Handy TerminalIf Scandisk finds a broken file or files, the screen on the right appears. (If any broken files exist, the screen on the r

22 BHT-904BB About “$$BRKLST.SYS” If Scandisk finds an invalid file(s), it will automatically create the "$$BRKLST.SYS" file. To check the

BHT-904BB Chapter 3 Basic Operation This chapter describes basic operations such as barcode reading, numeric data entry and item

iii BHT-904BB About this Manual  Due to improvements and so on, the content of this manual may be subject to change without prior notice.  The r

24 BHT-904BB 3.1 Reading Barcodes Follow the procedure below to read barcodes. 1. Turn the BHT power ON. Blue LED ONPower keyLight 2. Press the

25 Barcode Handy Terminal When unable to successfully read barcodes… Cause Countermeasure Specular reflection When the light is focused on the print

26 BHT-904BB 3.2 Numeric Data Entry Enter numeric data such as product volume with the numeric keys and Enter ( ) key. If numeric data is entered i

27 Barcode Handy Terminal 3.4 Changing the Default Settings The following settings can be changed at the MENU screen. Item Details Setting VOLUME

28 BHT-904BB 3. Use the [◄] and [►] cursor keys to select the setting. ～ 4. Press any of the following keys to exit the settings scr

29 Barcode Handy Terminal 3.5 Transmitting Data Three methods for transmitting data which the BHT collects to the host computer are possible; via Ir

30 BHT-904BB 3.5.1 IrDA communication  When performing data communication between BHT units Point the BHT IrDA communication ports toward each othe

31 Barcode Handy Terminal 3.5.2 Bluetooth® wireless communication Via Bluetooth®, wireless communication is possible with other Bluetooth® compatibl

32 BHT-904BB 3.5.3 USB Communication Request  Use a USB2.0 compatible mini-B cable, sold separately.  Connect the BHT to the USB port on

BHT-904BB Chapter 4 This chapter describes how to initialize and update the system, start up a user program, and operate System Mod

iv Barcode Handy Terminal Viewing this Manual  About the Bookmark The PDF Bookmark function can be used to jump to the Contents page. <Procedure

34 BHT-904BB 4.5.17 Updating the System (MODIFY MENU)････････････････････････････ 158

35 Barcode Handy Terminal4.1 Initializing the BHT System By initializing the system, program files and data files downloaded to the BHT user area ar

36 BHT-904BB 4.1.1 Selecting the Memory Area to be Initialized 1. Press the Power key ( ) while holding down the SF, M1 and [0] keys together. 2. Se

37 Barcode Handy Terminal4.1.2 Selecting the Message Version (English/Japanese/Simplified Chinese/Traditional Chinese/Korean/Thai) 1. When the screen

38 BHT-904BB 4.1.4 Performing System Initialization 1. The screen displays as shown on the right during system initialization. 2. Upon completi

39 Barcode Handy Terminal4.2 Updating the System 4.2.1 Updating the BHT System The BHT system update procedure is as follows. BHT System Update File

40 BHT-904BB 4.2.2 CU-911 System Update The CU-911 system update procedure is as follows. CU-911 System Update File Download ↓ CU-911 System Upda

41 Barcode Handy Terminal4.3 Executing User Programs User programs (application programs) can be executed using the following methods. Select the mo

42 BHT-904BB Several directory management program examples are given below. The names of the files used in these examples are as follows. MAIN.PD4

43 Barcode Handy Terminal (Example 3) Recommended download method After system initialization, first download the program to be executed simply by p

v BHT-904BB  Searching by Word The PDF search function can be used to jump to the target page by entering words or characters related to the item be

44 BHT-904BB 4.4 System Mode By starting up the BHT in System Mode and selecting each menu, the following operations can be performed individually.

45 Barcode Handy Terminal4.4.2 System Mode Basic Operation Menu Selection and Display Use the following procedure to select and display each menu. 1.

46 BHT-904BB Setting Value Selection  Operation example Use the following procedure to select setting values. Select the setting item with the

47 Barcode Handy Terminal4.4.3 SYSTEM MENU Configuration Menu Configuration for Items Displayed at the SYSTEM MENU Screen Select the item with the nu

48 BHT-904BB [7] and ENT keys Downloading/Uploading by FTP Refer to section “4.5.9Downloading/Uploading Files by FTP”. BS/C key DEVICE MENU 1:

49 Barcode Handy TerminalMenu Configuration for Items Not Displayed at the SYSTEM MENU Screen Press the corresponding numeric key while holding down

50 BHT-904BB 4.5 SYSTEM MENU 4.5.1 Executing Setup (“SETUP” menu) The BHT setup can be effectively executed using the BHT Setting and clone functions

51 Barcode Handy Terminal2. Execute the master-side setup. Setup is performed with the BHT Setting and other SYSTEM MENU functions. 3. Perform the se

52 BHT-904BB 5. Select “2: SLAVE” from the slave-side CLONE MENU. Master Side Slave Side 6. Align the BHTs as shown below and then press EN

53 Barcode Handy TerminalWhen communication is complete, the CLONE MENU (screen 1) reappears. In the event of a communication error, screen 2 appea

vi Barcode Handy Terminal Related Documentation  BHT-BASIC Programmer’s Manual (BHT-900 Series) This is an instruction manual used to create handy

54 BHT-904BB 4.5.2 Executing User Programs (EXECUTE PROGRAM Menu) Individually select and execute user programs downloaded to the BHT. Use the follow

55 Barcode Handy Terminal4.5.3 Downloading Files (DOWNLOAD Menu) Download files to the BHT user area from other devices such as the host computer. 

56 BHT-904BB 2. Select either “1: FILE” or “2: HT<-->HT COPY” and press the ENT The screen displays as shown on the right indicating that the B

57 Barcode Handy Terminal5. When downloading is complete, the beeper sounds once and the screen displays as shown on the right. hen using the Ymodem

58 BHT-904BB 4.5.4 Uploading Files (UPLOAD Menu) Upload files stored in the BHT user area to another device. Refer to “5.3.2 MTP Communication” Use t

59 Barcode Handy Terminal2. Select “1: FILE”, “2: ALL FILES” or “3: HT<-->HT COPY” and press the ENT key. he screen displays as shown on the ri

60 BHT-904BB 4. By executing the BHT-BASIC 4.0 Transfer Utility or similar program, the screen displays as shown on the right and file 5. ys as show

61 Barcode Handy Terminal4.5.5 Copying Files between 2 BHT Units Copy “all files (excluding font files)”, “setting data”, and the “date and time” san

62 BHT-904BB  Setting data which are copied between the BHT units ● settings ● ● Infrared light interface settings Key settings ● Remote wakeup s

63 Barcode Handy Terminal4.5.6 System Environment Settings (SET SYSTEM Menu) STEM” at the SYSTEM MENU and then press the ENT key. nu screen displays

vii BHT-904BB SAFETY PRECAUTIONS  Be sure to observe all these safety precautions. Please READ through this manual carefully. It will enable you to

64 BHT-904BB [1] Setting the auto-start execution program Use the following procedure to set the auto-start execution program. 1. Select “1: EXECUTE

65 Barcode Handy Terminal[2] Setting the message version, system status indication and screen display compatible mode tatus indication and screen

66 BHT-904BB 3. The SET DISPLAY menu displays as shown on the right. Use the cursor keys ([▲] [▼]) or numeric keys ([1] [2]) to highlight 5. ress th

67 Barcode Handy Terminal System Status Indication DescriptiTurning ON the system status indication displays the following icons at the bottom of t

68 BHT-904BB [4] Setting the special barcode reading parameters 1. Select “4: BARCODE” at the SET SYSTEM menu and thtThe SET BARCODE menu screenTh

69 Barcode Handy Terminal “2: DECODE LEVEL”: Decode level Set the decode level (barcode reading tolerance level). Press [◄] to decrease the setting

70 BHT-904BB  “2: OPEN BAR SETTINGS”: Setting for the “function in which the reading setting is 1. e BARCODE menu anE screen. : BUZZER/LED”: Buz

71 Barcode Handy Terminal[2] Buzzer/LED control 1. Select “2: BUZZER/LED” at the OPEN BAR SETTING menu and ppears. when the barcode is read g mechan

72 BHT-904BB [3] Read barcode Select [3: READ CODE] at the OPEN BAR SETTING menu and then reading to ON/OFF. The highlighted settings o change the s

73 Barcode Handy Terminal“1: EAN/UPC”: Detail setting of the EAN/UPC reading 1. tting screen appears. Enables or disables reading of the EAN-13/UPC-

viii Barcode Handy Terminal Handling the battery Mishandling of the battery may result in electrical shock, overheating, smoke generation, combusti

74 BHT-904BB EAN/UPC 3/3 (UPC-E setting) disables reading of the UPC-E. “2: 1ST CHARACTER”: Sets the first and second characters (country flag) of th

75 Barcode Handy Terminal“2 tting of the interleaved 2of5 (ITF) reading 1. S the SET BARCODE menu and then press the ENT key. ears. “1“2mum number

76 BHT-904BB “3: CODABAR”: Detail setting of the Codabar (NW-7) reading key. pears. gits. gits. 1. Select “3: CODABAR” at the SET BARCODE menu and t

77 Barcode Handy Terminal“4: CODE39”: Detail setting of the Code 39 reading 1. Select “4: CODE39” at the SET BARCODE menu and then press the ENT key.

78 BHT-904BB 2. Use the cursor keys ([▲] [▼]) or numeric keys ([1] [2]) to select the desired item. Press the cursor keys ([◄] [►]) to select the des

79 Barcode Handy Terminal(RSS-Limited setting) Enables or disables reading of the RSS-Limited (GS1 Databar Limited). (RSS-Expanded setting) Enables o

80 BHT-904BB “8: STF”: Detail setting of the standard 2of5 (STF) reading 1. SelecTh“1 Point  Always set the minimum number of digits to a number l

81 Barcode Handy Terminal[5] Setting the communication environment The communication environment settings following system initialization are foll

82 BHT-904BB U the communication environment settings 1. The SET COMMUNIC menu screen displays as shown on the r2. U ] [▼]) or numeric key to highl

83 Barcode Handy Terminal“2: PROTOCOL”: Communication protocol options setting screen Select “2: PROTOCOL” to display the screen shown on the right.